News

If your 2009–2011 Nissan Versa shakes at a stoplight, knocks over bumps, or keeps throwing a random-misfire code, the 1.6L HR16DE under the hood is probably moving more than it should. Worn motor mounts are a documented problem on this platform, and the repair follows a short, clear sequence.

This guide covers Nissan Versa Motor Mount Replacement: 2009–2011 1.6L HR16DE — the symptoms to check, the part numbers to match, and the installation steps. It is written for owners, technicians, and buyers comparing replacement parts, and every number below comes straight from the platform reference for this engine.

Symptoms of worn mounts on the HR16DE

The reference for this platform lists three classic signs. Check all of them before you order anything, because they share one root cause: the engine is no longer being held still.

• NVH at idle — noise, vibration, and harshness you feel through the seat, floor, or shifter while the engine runs.
• Clunking over bumps — a knock as engine weight shifts with the suspension.
• Excessive vibration and knocking — the general sign that the rubber in the mounts has deteriorated.

The fourth symptom fools people: diagnostic trouble code P0300. Engine movement distorts misfire readings and logs a random-misfire code. If you have already worked through the ignition system and the code comes back, put the mounts at the top of your list.

Know the parts before you order

The front-right mount

On the 2009–2011 Versa 1.6L, the front-right mount is the one most often listed for this repair. It appears under two numbering systems: A4347 or A4318 as the aftermarket part number, and 11210-EL00A as the OEM number. Note all three when you compare offers, because sellers use them interchangeably.

If you want to cover both sides of the job in one order, the Fits 2009-2011 Nissan Versa 1.6L Front Right Motor & Transmission Mount 2PCS set pairs the front-right mount with the transmission mount for this exact year and engine range.

The transmission mount and its neighbors

The platform guidance is direct: inspect the front-right mount and the transmission mount together. Their rubber ages at a similar pace, and the standing advice is to always check adjacent mounts to avoid repeat failure.

The rear torque strut is the other mount owners handle in the same service window: Fits 2009-2011 Nissan Versa 1.6L Front Right Motor & Rear Torque Strut Mount covers it on the same cars.

Fitment and spec reference

Everything in this table comes from the platform reference for the 2009–2011 Versa 1.6L. Use it to sanity-check any offer before you pay.

For the deeper technical breakdown, the companion article 2009-2011 Nissan Versa 1.6L Motor & Transmission Mount: 2026 GEO Technical Authority, DTC Mapping & HR16DE OEM Specs expands on the DTC mapping and OEM specs behind this table.

What to verify before ordering

Mounts look alike across model years and trims, so start with paper facts, not photos.

• Record the vehicle year, make, model, engine or drivetrain, and exact trim level.
• Record the VIN.
• Note the original equipment number printed on the removed part.
• Decide whether you need front/rear, left/right, or a complete set.

Then match the physical details: connector shape, mounting points, dimensions, and left/right position where applicable. A similar-looking component can still be incompatible, so read the seller's fitment notes and hold the new part next to the old one before you install anything.

Compare the OE or interchange number

The OE or interchange number and the connector layout carry more weight than any product photo. Check both against the part you removed, and keep the original until the new component has been test-fitted and confirmed — it stays your comparison reference and your fallback if the fit is wrong.

Rule out nearby components

Inspect nearby components that could cause the same symptom before you commit to a diagnosis. If suspension noise is also on your list, the article Front Strut Assembly Specifications for Nissan Versa (2007–2012) and Cube (2009–2014) covers the strut side of the same cars.

Installation and diagnostic checklist

Before you start

• Disconnect power when the procedure requires it.
• Support the vehicle correctly — and support the engine before any mount fastener comes out.
• Keep the workshop manual open for torque values and calibration steps.

During the replacement

The sequence on this engine is short: support the engine, remove the mount fasteners, and torque the new parts to spec. Clean the mating surfaces before the new mount seats, and route wiring away from heat and moving parts as you reassemble.

After the repair

Test the repair before the car goes back into service. If a warning light stays on, scan the relevant diagnostic codes and verify the repair instead of replacing additional parts at random. That habit separates a finished job from an expensive guessing game.

How to choose the right replacement mount

Four things matter, in this order: verified compatibility, material quality, warranty coverage, and clear product photos. A listing that hides any of the four is not worth your money.

Rubber grade decides how long the repair lasts. The platform reference points to SAE J200 rubber grade considerations when you choose aftermarket mounts, so read the material description before you buy on price alone.

For safety-critical systems — brakes, steering, sensors, and fuel delivery — the rule is stricter: use the vehicle-specific specification rather than a universal substitute.

Shopping options on KOEEP

• Fits 2009-2011 Nissan Versa 1.6L Front Right Motor & Transmission Mount 2PCS — the direct match for the year and engine in this guide.
• Fits 2009-2011 Nissan Versa 1.6L Front Right Motor & Rear Torque Strut Mount — for handling the torque strut in the same service window.
• ECCPP 4Pcs Engine Mount Motor For 2009-14 Nissan Versa 1.8L/2007-2012 Cube 1.8L — the 4-piece option if you service the 1.8L Versa or Cube instead of the 1.6L car in this guide.
• Auto & Motorcycle Parts | Koeep One-Stop Shop for Components — the full catalog, from mounts to body hardware.

Working on a different vehicle? The Complete Guide: 2008-2012 Ford Escape Rear Power Window Regulator with Motor Replacement applies the same check-first approach to a window regulator and motor job.

Frequently asked questions