News

Ford Focus Hood Release Cable Replacement (2012–2018) – BM5116A770AC is a practical reference for owners, technicians, and buyers comparing replacement parts. If the hood release lever on your 2012–2018 Focus feels loose, or the latch will not open, this guide tells you what to check, when to replace the cable, and how to verify the repair.

The part covered here is the hood release lever and latch cable for the 2012–2018 Ford Focus. The OEM reference is BM5116A770AC. You can order the Hood Latch Release Pull Handle Cable Lever for 2012–2018 Ford Focus (BM5116A770AC) directly from KOEEP.

Everything below follows the KOEEP fitting guide: what to verify before purchase, how to recognize the common symptoms, and how to plan a safe installation without relying on assumptions about year, trim, or engine configuration.

What the BM5116A770AC cable does

The cable links the interior hood release lever to the hood latch assembly. Pull the lever and the cable releases the latch. Years of pulls, moisture, and engine-bay heat can stretch, kink, or break the cable, and the lever itself can wear out. Any of those faults leaves you with a hood that will not open from the driver's seat.

KOEEP also lists companion parts for the same family on the C-MAX body: a Hood Latch Lock Release Cable & Handle Knob Lever for the 2012–2018 Ford Focus C-MAX and a Hood Latch Lock Release Cable for the Ford Focus C-Max 2012–2018, CV6Z-16916-A. If the number on your removed cable reads CV6Z-16916-A, compare it against that second listing as well.

Symptoms to look for

• The hood release lever feels loose when you pull it.
• The hood latch will not open, even with a firm pull.
• The cable shows damage along its run: stretched sections, kinks, or a break.

The guide's diagnostic order is simple. Begin by inspecting the hood release lever for damage, then trace the cable toward the latch assembly. If the cable is stretched, kinked, or broken, replace it with the BM5116A770AC cable instead of trying to re-bend a worn one.

What to verify before ordering

Start with the vehicle year, make, model, engine or drivetrain, and the original equipment number printed on the removed part. A similar-looking component can still be incompatible, so read the seller's fitment notes and compare the original part before installation.

• Record the VIN and exact trim level.
• Compare the OE or interchange number and connector layout.
• Check whether the part is front/rear, left/right, or a complete set.
• Inspect nearby components that could cause the same symptom.

Match connector shape, mounting points, and dimensions against your old cable, and check the left/right position where it applies. If anything is unclear, request a fitment quote from KOEEP with your VIN and the OE number before you pay.

See the BM5116A770AC hood release cable

Specs at a glance

Installation and diagnostic checklist

Follow the workshop manual for your exact trim — the guide keeps torque values and calibration steps there. The core sequence runs: inspect the release lever for damage, trace the cable toward the latch assembly, and fit the BM5116A770AC replacement when the cable is stretched, kinked, or broken.

Work safely while you are in there. Disconnect power when the procedure requires it, support the vehicle correctly, clean the mating surfaces, and route the new cable and its wiring away from heat and moving parts.

Test the repair before the vehicle goes back into service. The hood should open and close smoothly. Then check for relevant Ford diagnostic trouble codes (DTCs) to make sure no related electrical or latch system faults remain. If a warning light stays on, scan the codes and verify the repair instead of replacing additional parts at random.

How to choose the right replacement

Prioritize four things: verified compatibility, material quality, warranty coverage, and clear product photos. Good photos let you compare the connector layout and mounting points against your removed part before the box even ships.

The guide draws one firm line: for safety-critical systems such as brakes, steering, sensors, and fuel delivery, use the vehicle-specific specification rather than a universal substitute. Apply the same discipline here — stick to the exact OE reference and the stated 2012–2018 Focus fitment range.

Browse the wider KOEEP body parts collection to see latches, handles, cables, and body components grouped in one catalog, and check each listing's fitment notes against your VIN before ordering.

More KOEEP reading for Focus owners

Maintaining an older Focus too? The aluminum radiator guide for the 2000–2007 Ford Focus 2.0L 2.3L L4 (CU2296) walks through a complete radiator replacement on the earlier generation.

For the latch family on the C-MAX body style, the 2026 hood latch, cable, and handle knob lever technical consensus for the 2012–2018 Ford Focus C-MAX gathers the fitting detail in one place.

If you also service an Edge, Escape, Explorer, or Fusion from 2012–2018, the turbocharger oil supply line guide covers OE-spec material and DTC compliance points for that generation.

Frequently asked questions